02:23:50 Starting Observatory v1.63  12/8/14
02:23:50 Startup delay was 0 sec
02:23:50 Process ID=524  UTC is 2018-4-5  02:23:50.977; local time is 2018-4-5  02:23:50.977 Coordinated Universal Time (diff=0 min)
02:23:50 High-resolution performance counter is available; frequency is 2194.510000 MHz
02:23:50 Master has allocated shared memory
02:23:50 Reading parameter file ObservatoryControlFile.txt
02:23:50 Apparatus is type 2 (Alaska)
02:23:50 Detailed log 0
02:23:50 Pointing head type specified by Observatory control file is SkyScan
02:23:50 SkyScan model specified by Observatory control file is 0
02:23:50 Pointing head communications specified by Observatory control file via COM1
02:23:50 Station #5 location is lat=65.119000 deg N long=-147.430000 deg E  ht=200.000000 m
02:23:50 Corrections added to script-specified directions are az=0.000000, ze=0.000000
02:23:50 High-resolution performance counter has been disabled by Observatory control file
02:23:50 Filter type is 4
02:23:50 Name    Serial number Ry# Available? State  pRelay    1/0 USB shutters/relays specified
02:23:50   LASER           220            yes O 
02:23:50 Driver init  Result=78
02:23:50 Board name=""
02:23:50 Board entry="No Open Layers boards installed"
02:23:50 Board status=0
02:23:50 Get version result=0   SDK version is "V6.2.1.0"
02:23:50 Get driver version result=39   Version is "[unknown]"
02:23:50 Subsystem enumeration: nAD=0 nDA=0 nDIn=0 nDOut=0 nCtrTim=0 nDIOBits=0
02:23:50 Unknown digital I/O for this board; expected DT-302 (3 ports, configurable) or DT-9812 (2 ports, fixed) type
02:23:50 Digital I/O configure subsystem 0 as input
02:23:50 Set data flow result=40
02:23:50 Configure result=40
02:23:50 Digital I/O configure subsystem 0 as output
02:23:50 Set data flow result=40
02:23:50 Configure result=40
02:23:52 SkyScan init: port=COM1  logFile=Observatory_20180405022350.txt  detail=0
02:23:52 Init port COM1
02:23:52 Successful CreateFile
02:23:52 SetPortParameters: baud=9600  size=8  parity=0  stop=0  charTime=1042 usec
02:23:52 Successful SetCommTimeouts  ReadIntervalTimeout=104 ReadTotalTimeoutMultiplier=20  ReadTotalTimeoutConstant=10
02:23:52 SkyScan port init result=0
02:23:52 SkyScan SmartMotor 1 sample rate/firmware version result=0,10012 "24576/440C 
"
02:23:52 SkyScan SmartMotor 2 sample rate/firmware version result=0,10012 "24576/440C 
"
02:23:52 SkyScan SmartMotor 1 sw rev=25
02:23:52 SkyScan SmartMotor 2 sw rev=2
02:23:52 SkyScan SmartMotor 2 response was=2VERSION 100


02:23:52 SkyScan SmartMotor 1 (az) counts/rev=24000
02:23:52 SkyScan SmartMotor 2 (ze) counts/rev=24000
02:23:52 SkyScan initialization result=0
02:23:52 FilterWheelInit: FLISetDebugLevel err=0 debugFilepath is C:\PKZPrograms\FliDebug.txt  Level=7
02:23:52 FLIGetLibVersion err=0  Lib vn=Software Development Library for Windows 1.104
02:23:52 FLIList err=0  nWheels=1
02:23:52 Wheel 0 filename="flifil0"  modelName="CFW-6-6"
02:23:52 FLIOpen err=0  dev=0
02:23:52 FLIGetHWRevision err=0  hwRev=0
02:23:52 FLIGetFWRevision err=0  fwRev=32768
02:23:52 FLIGetFilterCount err=0  nFilters=6
02:23:52 FLIGetFilterPos err=0  currentPosition=-1
02:23:52 FLIGetStepsRemaining err=0  RemainingSteps=0
02:23:52 FilterWheelPositionGet err=0  currentPosition=-1 remaining steps=0
02:23:52 FLIFreeList err=0
02:23:52 Observatory log will be written every 1200000 msec
02:23:52 Received message from Master: op=Identify serial=111
02:23:57 Received message from Master: op=SetupFPI serial=115
02:23:57 SkyScan home
02:23:57 SkyScan home: resp=1
02:24:28 SkyScan home response=10000
02:24:28 Received message from Master: op=State serial=116
02:24:28 GetSingleValue result=40  Value=cccccccc
02:24:28 SkyScan query
02:24:28 SkyScan query done: ret=0  az=0<--12474  ze=45<-9000  Statuses=0009 0008
02:24:28 GetVoltage: Channel=3 Type=S Range=0.000000e+000 - 1.000000e+001 Cutoff filter freq=0.000000e+000
02:24:28 Parameters OK
02:24:28 Calc range=-1.000000e+001 - 1.000000e+001  Gain=1.000000e+000
02:24:28 Set A/D data flow result=40
02:24:28 Set A/D channel type result=40
02:24:28 Set A/D encoding result=40
02:24:28 Set A/D range -1.000000e+001 - 1.000000e+001  result=40
02:24:28 Set channel filter=0.000000e+000  result=40
02:24:28 Config A/D  Result=40
02:24:28 Get A/D range: -9.255963e+061 - -9.255963e+061  result=40
02:24:28 Get A/D filter: -9.255963e+061  result=40
02:24:28 Get A/D value=-858993460  result=40
02:24:28 Get analog voltage Code=-858993460 (2s' comp)  Voltage=-4.194304e+006 Result=40
02:24:28 GetVoltage: Channel=2 Type=S Range=0.000000e+000 - 1.000000e+001 Cutoff filter freq=0.000000e+000
02:24:28 Parameters OK
02:24:28 Calc range=-1.000000e+001 - 1.000000e+001  Gain=1.000000e+000
02:24:28 Set A/D data flow result=40
02:24:28 Set A/D channel type result=40
02:24:28 Set A/D encoding result=40
02:24:28 Set A/D range -1.000000e+001 - 1.000000e+001  result=40
02:24:28 Set channel filter=0.000000e+000  result=40
02:24:28 Config A/D  Result=40
02:24:28 Get A/D range: -9.255963e+061 - -9.255963e+061  result=40
02:24:28 Get A/D filter: -9.255963e+061  result=40
02:24:28 Get A/D value=-858993460  result=40
02:24:28 Get analog voltage Code=-858993460 (2s' comp)  Voltage=-4.194304e+006 Result=40
02:24:28 PH type=1  Digital in=000000  Instrument Az=0.000000 deg  Ze=45.000000 deg  T=-60.000000 deg  p=-10.000000  Err=0 Statuses=09 08
02:24:28 ParCount=11 Vn=163 DShFSR=6.286000e+003 Lat=6.511900e+001 Lon=-1.474300e+002 Ht=2.000000e+002 Sta=5
02:24:28 Aux=
02:24:28 Message to Master, serial 116 queued
02:24:28 Received message from Master: op=State serial=117
02:24:28 GetSingleValue result=40  Value=cccccccc
02:24:28 SkyScan query
02:24:29 SkyScan query done: ret=0  az=0<--12926  ze=45<-9000  Statuses=0009 0008
02:24:29 GetVoltage: Channel=3 Type=S Range=0.000000e+000 - 1.000000e+001 Cutoff filter freq=0.000000e+000
02:24:29 Parameters OK
02:24:29 Calc range=-1.000000e+001 - 1.000000e+001  Gain=1.000000e+000
02:24:29 Set A/D data flow result=40
02:24:29 Set A/D channel type result=40
02:24:29 Set A/D encoding result=40
02:24:29 Set A/D range -1.000000e+001 - 1.000000e+001  result=40
02:24:29 Set channel filter=0.000000e+000  result=40
02:24:29 Config A/D  Result=40
02:24:29 Get A/D range: -9.255963e+061 - -9.255963e+061  result=40
02:24:29 Get A/D filter: -9.255963e+061  result=40
02:24:29 Get A/D value=-858993460  result=40
02:24:29 Get analog voltage Code=-858993460 (2s' comp)  Voltage=-4.194304e+006 Result=40
02:24:29 GetVoltage: Channel=2 Type=S Range=0.000000e+000 - 1.000000e+001 Cutoff filter freq=0.000000e+000
02:24:29 Parameters OK
02:24:29 Calc range=-1.000000e+001 - 1.000000e+001  Gain=1.000000e+000
02:24:29 Set A/D data flow result=40
02:24:29 Set A/D channel type result=40
02:24:29 Set A/D encoding result=40
02:24:29 Set A/D range -1.000000e+001 - 1.000000e+001  result=40
02:24:29 Set channel filter=0.000000e+000  result=40
02:24:29 Config A/D  Result=40
02:24:29 Get A/D range: -9.255963e+061 - -9.255963e+061  result=40
02:24:29 Get A/D filter: -9.255963e+061  result=40
02:24:29 Get A/D value=-858993460  result=40
02:24:29 Get analog voltage Code=-858993460 (2s' comp)  Voltage=-4.194304e+006 Result=40
02:24:29 PH type=1  Digital in=000000  Instrument Az=0.000000 deg  Ze=45.000000 deg  T=-60.000000 deg  p=-10.000000  Err=0 Statuses=09 08
02:24:29 ParCount=11 Vn=163 DShFSR=6.286000e+003 Lat=6.511900e+001 Lon=-1.474300e+002 Ht=2.000000e+002 Sta=5
02:24:29 Aux=
02:24:29 Message to Master, serial 117 queued
02:24:29 Received message from Master: op=PointingHead serial=118
02:24:29 Move0 PH to az=0.000000e+000 (0.000000e+000)  zen=4.500000e+001 (4.500000e+001)
02:24:29 SkyScan point: az=0->0  ze=45->9000  Resp=0
02:24:29 Point started: ret=0
02:24:29 point_skyscan result=0
02:24:30 Check angles
02:24:30 SkyScan query
02:24:30 listen_skyscan result=10000 from ByChars "čRP "
02:24:32 listen_skyscan result=10000 from ByChars "ČRS "
02:24:32 Msec=0  True Az=-999  Ze=-999  Az status=0000  Ze status=FFFFFFFF
02:24:32 Message to Master queued w/err=0: serial=118 error=1
02:24:57 Received message from Master: op=PointingHead serial=119
02:24:58 Move0 PH to az=9.000000e+001 (9.000000e+001)  zen=4.500000e+001 (4.500000e+001)
02:24:58 SkyScan point: az=90->6000  ze=45->9000  Resp=0
02:24:58 listen_skyscan result=10000 from ByChars "če=0 "
02:24:58 point_skyscan result=10000
02:24:58 Check angles
02:24:58 SkyScan query
02:24:58 listen_skyscan result=10000 from ByChars "čRS "
02:24:58 Msec=0  True Az=-999  Ze=-999  Az status=FFFFFFFF  Ze status=FFFFFFFF
02:24:58 Error condition: state=-6 motor 2  Status=FFFFFFFF FFFFFFFF
02:24:58 Message to Master queued w/err=0: serial=119 error=1
02:25:23 Received message from Master: op=PointingHead serial=120
02:25:23 Move0 PH to az=1.800000e+002 (1.800000e+002)  zen=4.500000e+001 (4.500000e+001)
02:25:23 SkyScan point: az=180->12000  ze=45->9000  Resp=0
02:25:23 listen_skyscan result=10000 from ByChars "če=0 "
02:25:23 point_skyscan result=10000
02:25:24 Check angles
02:25:24 SkyScan query
02:25:24 listen_skyscan result=10000 from ByChars "čRS "
02:25:24 Msec=0  True Az=-999  Ze=-999  Az status=FFFFFFFF  Ze status=FFFFFFFF
02:25:24 Error condition: state=-6 motor 2  Status=FFFFFFFF FFFFFFFF
02:25:24 Message to Master queued w/err=0: serial=120 error=1
02:25:49 Received message from Master: op=PointingHead serial=121
02:25:49 Move0 PH to az=-9.000000e+001 (-9.000000e+001)  zen=4.500000e+001 (4.500000e+001)
02:25:49 SkyScan point: az=-90->6000  ze=45->15000  Resp=0
02:25:49 listen_skyscan result=10000 from ByChars "če=0 "
02:25:49 point_skyscan result=10000
02:25:50 Check angles
02:25:50 SkyScan query
02:25:50 listen_skyscan result=10000 from ByChars "čRS "
02:25:50 Msec=0  True Az=-999  Ze=-999  Az status=FFFFFFFF  Ze status=FFFFFFFF
02:25:50 Error condition: state=-6 motor 2  Status=FFFFFFFF FFFFFFFF
02:25:50 Message to Master queued w/err=0: serial=121 error=1
02:26:06 * END OF LOG *